Tools & Tuning

Collapsible service bench with 110cm x 50cm large aluminum bench top. Unique construction provides a professional World Cup work bench which is easily assembled from a few pieces. With extendable poles (Extract pole). Famous for its durability and strength. If used with a profile for waxing Nordic skis, this bench ONLY works with 5549885 Cross-Country Profile and Vise. If you are going to use this bench for Nordic with a profile on each side, you need to buy an extra Extract Pole in addition to the profiles. - Comes with one set of extract poles

The 15 mm thick base plate guarantees a constant temperature. The temperature of the wax iron is regulated and monitored by a microprocessor. Heating zone from 90–180 degrees. In the rear area/ the plate of the T18 is bent to simplify the application of JetStream 2.0. The front plate is flat to apply the gliding waxes evenly. This wax iron is especially suited for the handling of temperature-sensitive special and racing waxes. Iron cover included. - 110V

The 5 series is the hardest wax in the HS line, and is a great choice in cold conditions, due to its great durability and dry friction properties. It’s a great choice both for alpine and cross country. Despite being a wax for cold conditions, the melting point makes it easier to apply than many competitors in this area, without sacrificing the great glide properties. For fresh, old, or manmade snow. - HS5 can be used as a race wax alone or as a base for top coats. - Recommended iron temp: 150°C (311°F). - -10°C to -18°C (14°F to 0°F).

HS6 is very versatile. Its area of use stretches from underlayer for powder to racing wax and base prep wax for cold skis. HS6 has good durability and offers great performance on natural and artificial snow. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. HS6 can be used as a race wax alone or as a base for top coats. Recommended iron temp: 155°C (311°F). Highlights: - Fantastic allround glider - For training and competition - Great performance and durability - Fluoro-free and non-toxic - Exists also in liquid - Well tested on many conditions

HS7 performs great in normal winter conditions below the freezing point. Its hardness makes it convenient to work with and easy to get a good end-result. Can be used as a racing wax at low air humidity, but will also serve the purpose as a brilliant training wax. The speed of the iron should be approx. 8-10 sec. on a skating ski or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. HS7 can be used as a race wax alone or as a base for top coats. Recommended iron temp: 150°C (302°F). Highlights: - Fantastic allround-glider - For training and competition - Great performance and durability - Fluoro-free and non-toxic - Well tested on many conditions

A great wax for both base-prep and training. It can also be used as a race wax, preferably used with a top coat. Easy to melt and very convenient to work with. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 150°C (302°F). Replaces the LF8X. Highlights: - Easy to work with - For training and competition - Great performance and durability - Fluoro-free and non-toxic - Well tested on many conditions

TS5B - Top Speed 5 Black. Excellent dry-friction properties! The TSB series are gliders for competition that works extremely well on dirty snow and when dry friction conditions. The 5 series is the hardest wax in the TSB line, and is a great choice in cold conditions, both for alpine and cross country. It is loved by servicemen, due to its great durability and properties when the snow is dirty. This is achieved thanks to the black solid lubricant additive that also reduces friction when very cold snow. Despite being a wax for cold conditions, the melting point makes it easier to apply than many competitors in this area, without sacrificing the great glide properties. The speed of the iron should be approx. 8-10 sec. on a skating ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Scraping after approx. one minute. Important to have a good iron to get an efficient melting of the wax. TS5B can be used as a race wax alone or as a base for top coats. Recommended iron temp.: 160°C (320°F)

TS6B - Top Speed 6 Black. An undisputed favorite in cold conditions! The TSB series are gliders for competition that works extremely well on dirty snow and when dry friction conditions. The TS6B is the second hardest wax in the TSB line, and is a great choice in typical winter conditions, both for alpine and cross country. It is loved by servicemen, due to its great durability and properties when the snow is dirty. This is achieved thanks to the black solid lubricant additive that also reduces friction when very cold snow. Despite being a wax for cold conditions, the melting point makes it easier to apply than many competitors in this area, without sacrificing the great glide properties. The speed of the iron should be approx. 8-10 sec. on a skating ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Scraping after appr. one minute. Important to have a good iron to get an efficient melting of the wax. TS6B can be used as a race wax alone or as a base for top coats. Recommended iron temp.: 155°C (311°F).

TS7B - Top Speed 7 Black. A great racing wax for typical winter conditions! The TSB series are gliders for competition that works extremely well on dirty snow and when dry friction conditions. TS7B is a versatile wax suited for normal winter conditions below the freezing point. Its hardness makes it convenient to work with and easy to get a good end-result. The solid lubricant additive reduces the friction in cold conditions and in contaminated snow. It’s a very popular wax both in alpine and cross country and has shown good properties on artificial snow in addition to natural, transformed older snow. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. TS7B can be used as race wax alone but is often used as base for top coats. Recommended iron temp: 150°C (302°F).

TS8 - Top Speed 8 red. Great dirt resistance! The TSB series are gliders for competition that works extremely well on dirty snow and when dry friction conditions. TS8B is made harder than the std TS8. The adjusted hardness makes the wax more durable and absorbs less dirt. The solid lubricant additive reduces the friction in contaminated snow. Excellent results in artificial snow as well as natural transformed older snow, especially noticeable when used alone. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. TS8B can be used as race wax alone but is often used as a base for top coats. Recommended iron temp: 150°C (302°F).

Waxing profile for cross country skis. Stable economy profile in aluminum and plastic. Lightweight and easy to adjust. Same profile at front and rear so can be used in both directions. Consists of two parts (each approx. 110 cm) that fit into each other and thereby take up little space for transport and storage. Adjustable in length from 150 cm to 210 cm. Can be used with legs T0079-1 or T0790-K clamps. Weight: 1.8 kg. - Waxing profile - For prepping cross-country skis - For keen cross country skiers - Lightweight and easy to adjust

Ergonomically shaped surface structuring device with interchangeable structure roller for easy structuring of the running surface of cross country skis. Structuring significantly improves the sliding properties of skis. As a kit/ the device is supplied with all three rollers (yellow/red/blue) and ensures optimally structured skis in all snow conditions and temperatures. - Comes with Structurite form and all 3 rollers (yellow/ red/ and blue)

Space efficient and stable! Wax table, perfect at home or at events. Waxing table that is easy to fold together. Comes with four rubber feet for anti slip. One leg adjustable for better stability on uneven surfaces. Adjustable height: 87 cm, 85 cm or 75 cm. Fits two sets of cross country waxing profiles (T0766). Table top 120 cm x 35 cm. Net. weight: 11 kg/24 lbs.

Hard high performance racing wax to meet the highest demands. The wax used by World Cup stars! Features: - For cold and aggressive snow conditions - Perfect sliding properties - Maximum water and dirt repulsion - Unmatched degree of hold - Best bonding agent for Top Finish products - Resealable wax case

Medium-hard high performance racing wax to meet the highest demands. The wax used by World Cup stars! Features: - Wide range of use in medium snow temperature conditions - Perfect sliding properties - Maximum water and dirt repulsion - Unmatched degree of hold - Best bonding agent for Top Finish products - Resealable wax case

Soft high performance racing wax to meet the highest demands. The wax used by World Cup stars! features: - For high-moisture and wet snow conditions - Perfect sliding properties - Maximum water and dirt repulsion - Unmatched degree of hold - Best bonding agent for Top Finish products - Resealable wax case

PS10 is an economic training and racing wax as well as base prep wax for warm skis. Easy to melt and very convenient to work with. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 120°C (248°F). - A versatile wax for warm conditions - Low melting point and easy to apply

The PS5 is the hardest wax in the line, and is a great choice in cold conditions, due to its great durability and dry friction properties. It's a great choice both for alpine and cross country. Despite being a wax for cold conditions, the melting point makes it easier to apply than many competitors in this area, without sacrificing the great glide properties. For fresh, old, or manmade snow. The speed of the iron should be approx. 8-10 sec. on a skating ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Scraping after appr. one minute. Important to have a good iron to get an efficient melting of the wax. PS5 can be used as a race wax alone or as a base for top coats. Recommended iron temp: 150°C (311°F) - Recommended iron temp: 150°C (311°F). - Replaces the CH5X. - -10°C to -18°C (14°F to 0°F).

PS6 is very versatile. Its area of use stretches from underlayer for powder to racing wax and base prep wax for cold skis. PS6 has good durability and offers great performance on natural and artificial snow. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. Important to have a good iron to get an efficient melting of the wax. PS6 can be used as a race wax alone or as a base for powders and other top coats. Recommended iron temp: 145°C (293°F). - Recommended iron temp: 145°C (293°F). - Replaces the CH6X - -6°C to -12°C (21°F to 10°F).

PS7 is a wax that performs great in normal winter conditions below the freezing point. Its hardness makes it convenient to work with and easy to get a good end result. PS7 is an economic training and racing wax as well as an all-round base prep wax. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 140°C (284°F). - Recommended iron temp: 140°C (284°F). - Replaces the CH7X. - -2°C to -8°C (28°F to 18°F).

PS8 is an economic training and racing wax as well as base prep wax for warm skis. Easy to melt and very convenient to work with. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 130°C (266°F). - Recommended iron temp: 130°C (266°F). - Replaces the CH8X. - -4°C to +4°C (25°F to 39°F).

Waxing profile for when you are traveling. For prepping cross-country skis. - Travel profile - For cross-country skis - For skiers on the go - Takes up minimal space

HS10 is a great base prep wax, but also a great training wax. Ideal in warm conditions, typically during spring skiing. For racing, we recommend going with a top coat as the final layer. The speed of the iron should be approx. 8-10 sec. on a skating or alpine ski. The wax can be re-heated after cooling to room temperature (10 min) for better durability. It's important to have a good iron to get an efficient melting of the wax. Recommended iron temp: 150°C (302°F). Details: - A popular wax in nordic disciplines - Good water repellent properties - Replaces LF10X - For training and competition Highlights: - For warm conditions - Easy to work with - For training and competition - Great performance and durability - Fluoro-free and non-toxic - Well tested on many conditions

Merino wool, 100mm version, 20mm long wool hairs. A new and revolutionary way of applying waxes without the need of a waxing iron. The method is tailor-made for harder waxes, such as the Marathons and is applied onto the skis in two simple steps: Start by applying the wax to the roto brush by touching the wax to the wool for a few seconds while running the drill at a speed of approx. 1.500 RPM. Then, use the roto brush on the base with a speed of approx. 1.500 RPM. Use light pressure. Start from the tip and move back and forth approx. a foot at a time towards the tail (three times applying the wax and three times polishing). - Roto wool - Trendy waxing technique - Used in World Cup - Perfect with fluoro free ski wax - Easy to use - No heat needed

Racing favorite! High quality roto fleece. Effectiv when there are many skis or boards to prepare. The Fleece-Roto improves Cera F Powder and Cera F Solid performance. Apply the Cera powder to the base with a wax iron first. The Fleece-roto should be used a couple of times to get optimal performance. NB! Use separate Fleece brushes for each type of Cera F. 100 mm wide.

Designed specifically for wet conditions and dirty snow. The black additive helps reduce friction and reduces the amount of dirt that sticks to the base. As well as being superb in wet conditions, this wax is also highly competitive in colder weather. The speed of the waxing iron should be approx. 8-10 seconds for a skating or alpine ski. The wax can be reheated after cooling to room temperature (10 min.) for better durability. Scrape after waiting about one minute. It is important to have a good waxing iron in order to melt the wax efficiently. Recommended waxing iron temp.: 155°C. - Durable glide wax - A favorite for classic long-distance skiing - Hard wax - Can be used with roto wool - For all skiing - Ski wax

Designed specifically for longer distances on newer and clean snow. Excellent in warm conditions, but also very competitive at lower temperatures. The speed of the waxing iron should be approx. 8-10 seconds for a skating or alpine ski. The wax can be reheated after cooling to room temperature (10 min.) for better durability. Scrape after waiting about one minute. It is important to have a good waxing iron in order to melt the wax efficiently. Recommended waxing iron temp.: 155°C.

A liquid topping designed for racing use. Specifically designed for cold conditions, down to -12°C. TS06L is a versatile wax that works well in all snow conditions, but is at its best when humidity is high. Hold the bottle 10-15 cm above the ski base and spray on a thin layer. To even out the product and remove excess liquid, we recommend brushing with a felt cork (T0021) immediately after application. Then allow the product to dry and polish with a nylon brush. For better wear resistance, we recommend rubbing in the product using Roto fleece (T0018F-2) after it has dried and then polish it with a nylon brush. - Liquid yet durable - Excellent as a topping base - Gives excellent glide in cold conditions - Swix’s TS-series liquid glide wax was recommended during the 2021 World Ski Championships

The easiest way to achieve good glide for racing or training. Recommended at temperatures from -2°C to -8 degrees. - Liquid yet durable - Excellent as a topping base - Gives good glide in varied conditions - Swix’s TS-series liquid glide wax was recommended during the 2021 World Ski Championships

TS10B is harder than the other T10’ products of the PRO system. The extra hardness makes the wax more robust and so absorbs less dirt. The black additive reduces friction in polluted snow. This is particularly noticeable when the wax is used alone. The wax has very good test results on artificial snow and snow transformed into old natural snow. The speed of the waxing iron should be approx. 8-10 seconds for a skating or alpine ski. The wax can be reheated after cooling to room temperature (10 min.) for better durability. It is important to have a good waxing iron in order to melt the wax efficiently. TS10B can be used as a racing wax alone, but is also often used as a base wax for other racing products. Recommended waxing iron temperature 165°C. - Liquid yet durable - Excellent as a topping base - Ensures a smooth glide in warm conditions - Swix’s TS-series liquid glide wax was recommended during the 2021 World Ski Championships